HCA Admin
Sep 01, 2009, 01:22 PM
Sometimes the SmartHome 2414U PowerLinc gets into a state with a variety of symptoms. Some of them are:
Flashing status LED on the 2414U.
Very sluggish response when sending ON/OFF/DIM commands outbound
Non-response inbound from the Insteon signals. HCA doesn't show a log entry for receipt of a command, almost as if the 2414U had only its "outbound" brain available.
"No response" returned from "get status" commands, etc. There are two possible resolutions for this problem. Try this one first:
Disconnect the USB cable then remove the 2414 from the outlet, wait about 1 minute, reconnect the USB cable, press and hold the reset button for about 10 seconds and while still holding the button in, insert it into the outlet and still hold the button in for another 10 seconds then release. This will reset the PowerLinc.
If the 2414U LED turns to a steady ON after a few seconds there is one last task. Start HCA and from the menu choose:
HCA - Hardware - Insteon - Insteon PLC Utilities
And press the "Add Devices" button. This updates the table inside the 2414U that contains the address of all your devices. This is necessary so the 2414U will pass messages from those devices to HCA.
If this simple fix doesn't work then try this more complex method. For this you need to reset the application that runs inside the 2414U. HCA can not do this. You must use software available from SmartHome.
Go here to download the application you need:
http://www.smarthome.com/Files/2814ub.zip
If SmartHome changes their pages, which they do now and then, use the Google Search Engine to look for "Smarthome Manager Essential Timer"
Next, shutdown HCA using File - Shutdown (Not File - Exit). Then install the SmartHome application and start it - if it wants to upgrade itself from the web let it. Select from the menu:
Setup - Options - Reset Timer Application
This usually clears the problem. The PowerLinc LED turns to solid "ON". Exit the Smarthome application, then restart HCA.
Again, like the first fix described above, you must follow the instructions for updating the 2414U link table using the HCA menu pick.
If you are still having problems with getting your 2414U to work with HCA after these fixes, please contact technical support.
Why this problem occurs with the 2414U remains under investigation. To the best of our understanding, HCA is not sending any incorrect commands to the 2414U or in any way not using the 2414U correctly.
Flashing status LED on the 2414U.
Very sluggish response when sending ON/OFF/DIM commands outbound
Non-response inbound from the Insteon signals. HCA doesn't show a log entry for receipt of a command, almost as if the 2414U had only its "outbound" brain available.
"No response" returned from "get status" commands, etc. There are two possible resolutions for this problem. Try this one first:
Disconnect the USB cable then remove the 2414 from the outlet, wait about 1 minute, reconnect the USB cable, press and hold the reset button for about 10 seconds and while still holding the button in, insert it into the outlet and still hold the button in for another 10 seconds then release. This will reset the PowerLinc.
If the 2414U LED turns to a steady ON after a few seconds there is one last task. Start HCA and from the menu choose:
HCA - Hardware - Insteon - Insteon PLC Utilities
And press the "Add Devices" button. This updates the table inside the 2414U that contains the address of all your devices. This is necessary so the 2414U will pass messages from those devices to HCA.
If this simple fix doesn't work then try this more complex method. For this you need to reset the application that runs inside the 2414U. HCA can not do this. You must use software available from SmartHome.
Go here to download the application you need:
http://www.smarthome.com/Files/2814ub.zip
If SmartHome changes their pages, which they do now and then, use the Google Search Engine to look for "Smarthome Manager Essential Timer"
Next, shutdown HCA using File - Shutdown (Not File - Exit). Then install the SmartHome application and start it - if it wants to upgrade itself from the web let it. Select from the menu:
Setup - Options - Reset Timer Application
This usually clears the problem. The PowerLinc LED turns to solid "ON". Exit the Smarthome application, then restart HCA.
Again, like the first fix described above, you must follow the instructions for updating the 2414U link table using the HCA menu pick.
If you are still having problems with getting your 2414U to work with HCA after these fixes, please contact technical support.
Why this problem occurs with the 2414U remains under investigation. To the best of our understanding, HCA is not sending any incorrect commands to the 2414U or in any way not using the 2414U correctly.